A chocolate textured accessory box for drinks and smartphones. Can be attached with super clamps or innovative adapters. https://www.instagram.com/reel/C-kGcFQvgJx/?igsh=MTZmeHE0YW42aWc4dQ== https://www.instagram.com/reel/C-M7NLWPDBy/?igsh=M3N3cHB2NXcyNTVi (x1)Mini Chocolate Front Box (x2) adapter for super clamps (x2)M5 bolts

● Precautions before purchasing This product is made from 3D-printed resin, not metal. If you are expecting metal-like strength or finish, please refrain from purchasing. Due to the nature of 3D printing, layer lines, minor surface marks, or small burrs may be present. Fine scratches may also occur during the manufacturing process. Compared to injection-molded resin products, 3D-printed items generally have a more handcrafted appearance. The strength of this product has been tested and confirmed for normal use. However, please avoid excessive force, impact, or improper use, as this may cause damage. We kindly ask that only customers who understand and accept the characteristics of 3D-printed and handmade products place an order. ● Product explanation This compact trash can can be mounted to a V-lock just like a V-mount battery. Since the V-lock system is widely used in camera and lighting equipment, it can be attached in many different places on set. The V-lock mount allows for quick and easy attachment and removal, making trash disposal fast and hassle-free during shoots. https://www.instagram.com/reel/DUDZwL3Eug-/?igsh=dnA5bWx1b3dzZHU5 We have confirmed the installation with many V-mounts, but there may be some wobbling depending on the receiving side of the V-lock. Checked V-mount list ・SmallRig Mini V-Lock Assembly Kit MD2801B ・SmallRig Mini V Mount Battery Plate 2987 ●Dimensions 　Approx.　100mm x 85mm x 140mm ●Package contents (The first photo is the content) V-lock Trash Can

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation It allows you to attach the V-Lock Base and Cheese Plate to your ROBOCUP. https://www.instagram.com/reel/DSUrkspkuCY/?igsh=MTRyaXp3YjN0dmEycg== Products that have been confirmed for installation ・SmallRig Mini V-Lock Assembly Kit MD2801B ・SmallRig Mini V Mount Battery Plate 2987 ・SmallRig Mounting Cheese Plate 1598 ●Package contents (The first photo is the content) 1 - Camera Screw Mount Holder for ROBOCUP 2 - Velcro for fixing　

● ご購入前の注意事項 本製品は3Dプリント樹脂製であり、金属ではありません。金属のような強度を期待される方はご購入をお控えください。 3Dプリント製品には、積層痕やバリ、製造工程で発生する微細な傷などが生じる場合があります。通常、3Dプリント製品は、型で製造された樹脂製品のようにきれいな仕上がりになることは稀です。製品の強度は通常使用において確認しておりますが、過度の負担をかけるような使用や加工はしないでください。 上記の通り、3Dプリント製品、またはハンドメイド製品であることをご理解いただける方のみご注文ください。 ● 商品説明 「ビオレu 薬用手指の消毒液」を ROBOCUPに固定できるホルダーです。 ●パッケージ内容（写真1枚目が内容物です） ・消毒液ホルダー for ROBOCUP ・固定用マジックテープ　２本

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a dock for Magliner that can hold an Velbon Dolly Pod. You can also take it apart, attach the super clamps. Designed it based on the Velbon Dolly Pod DP-83S that is mainstream in Japan. [upper “grip” ] 28-32mm grip for Velbon Dolly Pod DP-83S [lower “base”] base for Velbon Dolly Pod DP-83S It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the Dolly Pod to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - DPD-1 This grip can hold stands with a diameter of approximately 28-32mm. (x1)- upper “grip” with black clamp and orange safety lock This grip can hold stands with a diameter of approximately 28-32mm. (x1)- lower “base” for Velbon Dolly Pod The lower “base” for securing the pod (x1)- Mini lower “base” for Velbon Dolly Pod The lower “base” for securing the pod to the handle side of the Magliner 1-Mini Magliner adapter for DPD-1 (x2) Magliner adapter (x4) M5 bolts (x1) 1/4inch bolt for bottom 2 - screw and bolt pack (x2) stainless steel 1/4-20 screws (x4) stainless steel M5-15mm bolts 2 - Rubber-like spacer with 3 holes

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a dock for Olympia carts that can hold an Velbon Dolly Pod. https://www.instagram.com/reel/DNaik4Qvgkp/?igsh=MWJtam91aGwycjZzNw== https://www.instagram.com/reel/DPv4vQgEm8d/?igsh=bjkyNHo1cXZlMGt2 You can also take it apart, attach the super clamps. Designed it based on the Velbon Dolly Pod DP-83S that is mainstream in Japan. It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the Dolly Pod to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - Dolly Pod Dock（DPD-1） This grip can hold stands with a diameter of approximately 28-32mm. [upper “grip” & extension parts ] 28-32mm grip for Velbon Dolly Pod DP-83S [lower “base”] base for Velbon Dolly Pod DP-83S 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws (x4) stainless steel M5-15mm bolts 2 - Rubber-like spacer with 3 holes 1 - Olympia adapter for DPD-1 / Two mounting screws Can be fixed to 3.5mm thick edges (x1) upper Olympia adapter with two mounting screws (x1) long Olympia adapter with two mounting screws (This allows you to adjust the mounting height.) (x4) stainless steel M5-25mm bolts (x1) stainless steel 1/4"-25mm bolts (x2) stainless steel M5-15mm bolts (x1) stainless steel 1/4"-16mm bolts (x4) stainless steel M5 nuts (x1) stainless steel 1/4" nuts

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a boom & umbrella dock that can be attached to an Olympia cart. Also, it is a boom & umbrella dock that can be fixed with a super clamp. It is possible to connect to the side and install booms side by side. https://www.instagram.com/reel/DM2dwQSPaZw/?igsh=eGd4ZHF2bnY1YWR1 https://www.instagram.com/reel/DM5EPX4vWeB/?igsh=enZjMG0weWxxanFx Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with two M5 bolts and one 1/4 inch screw. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. https://www.instagram.com/reel/C94U2EevdWI/?igsh=MWQ0bG9jNTlidHpzYw== The lower base part has a structure that does not accumulate water such as rain, making it easy to clean. The whole material uses weather resistance and durable ASA, and the grip uses high -quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with black clamp and orange safety lock This grip can hold stands with a diameter of approximately 32-36mm. 1 - lower “base” 2 - Rubber-like spacer with 3 holes 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts 1 - Olympia adapter for BUD-1 & LSD-1 / Two mounting screws Can be fixed to 3.5mm thick edges (x1) Olympia upper adapter with two mounting screws (x1) Olympia bottom adapter with two mounting screws (x4) stainless steel M5-25mm bolts (x4) stainless steel M5 nuts (x1) Wedge spacer set

●Package contents (The first photo is the content) An adapter for easily attaching a boom and a light stand to Olympia carts To install the adapter and BUD-1 or LSD-1, you will need to remove the non-slip rubber-like sheet. Fix with M5 bolts and M5 nuts to connect the adapter. Designed wedges to allow you to adjust the mounting angle. The dock is designed to attach horizontally to the vertical edge of a cart. However, carts vary in manufacturing precision, and some may not be vertical. Added three wedges of different angles so you can adjust the mounting position to your cart. (x1) Olympia upper adapter / two mounting screw Can be fixed to 3.5mm thick edges (x1) Olympia bottom adapter / two mounting screw Can be fixed to 3.5mm thick edges (x4) M5 bolts (x4) M5 nuts (x1) Wedge spacer set

●Package contents (The first photo is the content) An adapter for easily attaching a boom and a light stand to Olympia carts To install the adapter and BUD-1 or LSD-1, you will need to remove the non-slip rubber-like sheet. Fix with M5 bolts and M5 nuts to connect the adapter. (x2) Olympia adapter / Two mounting screw (x2) M5 bolts 25mm (x1) 1/4" bolts 25mm (x2) M5 bolts 15mm (x1) 1/4" bolts 16mm (x2) M5 nuts (x1) 1/4" nuts (x1) Wedge spacer set

●Package contents (The first photo is the content) An adapter for easily attaching a boom and a light stand to Olympia carts To install the adapter and BUD-1 or LSD-1, you will need to remove the non-slip rubber-like sheet. Fix with M5 bolts and M5 nuts to connect the adapter. Designed wedges to allow you to adjust the mounting angle. The dock is designed to attach horizontally to the vertical edge of a cart. However, carts vary in manufacturing precision, and some may not be vertical. Added three wedges of different angles so you can adjust the mounting position to your cart. (x1) Olympia upper adapter / One mounting screw Can be fixed to 3.5mm thick edges (x1) Olympia bottom adapter / One mounting screw Can be fixed to 3.5mm thick edges (x4) M5 bolts (x4) M5 nuts (x1) Wedge spacer set

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a boom & umbrella dock that can be attached to an Olympia cart. Also, it is a boom & umbrella dock that can be fixed with a super clamp. It is possible to connect to the side and install booms side by side. https://www.instagram.com/reel/DM2dwQSPaZw/?igsh=eGd4ZHF2bnY1YWR1 https://www.instagram.com/reel/DM5EPX4vWeB/?igsh=enZjMG0weWxxanFx Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with two M5 bolts and one 1/4 inch screw. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. https://www.instagram.com/reel/C94U2EevdWI/?igsh=MWQ0bG9jNTlidHpzYw== The lower base part has a structure that does not accumulate water such as rain, making it easy to clean. The whole material uses weather resistance and durable ASA, and the grip uses high -quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with black clamp and orange safety lock This grip can hold stands with a diameter of approximately 32-36mm. 1 - lower “base” 2 - Rubber-like spacer with 3 holes 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts 1 - Olympia adapter for BUD-1 & LSD-1 Can be fixed to 3.5mm thick edges (x1) Olympia upper adapter (x1) Olympia bottom adapter (x4) stainless steel M5-25mm bolts (x4) stainless steel M5 nuts (x1) Wedge spacer set

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a combo that can hold three booms. It comes pre-assembled, so all you need to do is attach the super clamp. It is a boom & umbrella dock that can be fixed with a super clamp. It is possible to connect to the side and install booms side by side. Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with one M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. The lower base part has a structure that does not accumulate water such as rain, making it easy to clean. There is also an optional non -slip sheet. Glue the non -slip sheet with your favorite double -sided tape or adhesive. The whole material uses weather resistance and durable ASA, and the grip uses high -quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 3 - upper “grip” with black clamp and orange safety lock 　Please select one of the four grips below with the corresponding diameter. ①Approximately 22-25mm ②Approximately 28-32mm ③Approximately 32-36mm ④Approximately 38-42mm 3- lower “base” 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws (x4) stainless steel M5-15mm bolts 1- Spacer pack “A” for BUD-1

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a combo that can hold three C-stands. It comes half-assembled, so you need to connect the docks like the video in the link below. https://www.instagram.com/reel/C95GFm8vNFp/?igsh=dTN5eWR0MDVlbnNx It is a C-stand dock that can be fixed with a super clamp. It is possible to connect to the side and install C-stands side by side. To hold one C-stand, you need a C-stand dock and two super clamps. One C-Stand weighs approximately 5kg-10kg, and most Super Clamps have a maximum payload of 15kg. When connecting the docks, do not load C-Stands that are heavier than the Super Clamp's load capacity. Designed it based on the Matthews C-stand that is mainstream in Japan. The base of the current design is designed so that not only a C-stand, but also a boom or umbrella can be placed on the bottom. If you use the Turtle Base C-stand, which has a protrusion at the bottom, you may hit the bottom, so a base with a larger hole is required. The type is coming soon. [upper “grip” ] Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with one 1/4 inch screw and two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with  one M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. [lower “base”] C-stand can be installed at different angles of 90 degrees. https://www.instagram.com/reel/C8HB8bqPbE4/?igsh=eXZpcm81dWx4aG4z It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. In addition, it is possible to connect to the side with two M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the C-stand to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 3 - upper “grip” with black clamp and RED safety lock 　Please check the diameter of your stand before purchasing. This grip can hold stands with a diameter of approximately 32-36mm. 3- lower “base” for Matthews C-stands 3 - screw and bolt pack (x2) stainless steel 1/4-20 screws (x4) stainless steel M5-15mm bolts 1-Spacer pack for CSD-1 3- Y-shaped Wedge for Magliner Tube Frame

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a combo that can hold three C-stands. It comes half-assembled, so you need to connect the docks like the video in the link below. https://www.instagram.com/reel/C95GFm8vNFp/?igsh=dTN5eWR0MDVlbnNx It is a C-stand dock that can be fixed with a super clamp. It is possible to connect to the side and install C-stands side by side. To hold one C-stand, you need a C-stand dock and two super clamps. One C-Stand weighs approximately 5kg-10kg, and most Super Clamps have a maximum payload of 15kg. When connecting the docks, do not load C-Stands that are heavier than the Super Clamp's load capacity. Designed it based on the Avenger C-stand that is mainstream in Japan. The base of the current design is designed so that not only a C-stand, but also a boom or umbrella can be placed on the bottom. If you use the Turtle Base C-stand, which has a protrusion at the bottom, you may hit the bottom, so a base with a larger hole is required. The type is coming soon. [upper “grip” ] Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with one 1/4 inch screw and two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with  one M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. [lower “base”] C-stand can be installed at different angles of 90 degrees. https://www.instagram.com/reel/C8HB8bqPbE4/?igsh=eXZpcm81dWx4aG4z It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. In addition, it is possible to connect to the side with  two M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the C-stand to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 3 - upper “grip” with black clamp and orange safety lock 　Please check the diameter of your stand before purchasing. This grip can hold stands with a diameter of approximately 32-36mm. 3- lower “base” for C-stands 3 - screw and bolt pack (x2) stainless steel 1/4-20 screws (x4) stainless steel M5-15mm bolts 1-Spacer pack for CSD-1 3- Y-shaped Wedge for Magliner Tube Frame

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation You can attach V-lock to mobile batteries, smartphones, etc. V-lock allows for easy installation and removal https://www.instagram.com/reel/DAxtcEoPWc_/?igsh=cHZtbmpiZXVuc3ht https://www.instagram.com/reel/C_nDnt-PjDM/?igsh=MWZqdXMzOHVxeDlkaw== https://www.instagram.com/reel/C_7pZvGxqpu/?igsh=Y3JwYzRmYjl2dXo1 We have confirmed the installation with many V-mounts, but there may be some wobbling depending on the receiving side of the V-lock. Checked V-mount list ・SmallRig Mini V-Lock Assembly Kit MD2801B ・SmallRig Mini V Mount Battery Plate 2987 ・NEP GP-TS mini V /Pro-X Mini Sharkfin Hotswap Adapter V Mount ●Dimensions 　Approx.　65mm x 42mm x 6.7mm ●Package contents (The first photo is the content) (x2) V-lock Sticker Mini (x2) Strong double-sided tapes [MADE IN JAPAN] 　　*Need to cut to fit the shape (x1) Toy V-lock Base (x2) 1/4 camera screws

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation You can attach V-lock to mobile batteries, smartphones, etc. V-lock allows for easy installation and removal https://www.instagram.com/reel/DAxtcEoPWc_/?igsh=cHZtbmpiZXVuc3ht https://www.instagram.com/reel/C_nDnt-PjDM/?igsh=MWZqdXMzOHVxeDlkaw== https://www.instagram.com/reel/C_7pZvGxqpu/?igsh=Y3JwYzRmYjl2dXo1 We have confirmed the installation with many V-mounts, but there may be some wobbling depending on the receiving side of the V-lock. Checked V-mount list ・SmallRig Mini V-Lock Assembly Kit MD2801B ・SmallRig Mini V Mount Battery Plate 2987 ・NEP GP-TS mini V /Pro-X Mini Sharkfin Hotswap Adapter V Mount ●Dimensions 　Approx.　80mm x 42mm x 6.7mm ●Package contents (The first photo is the content) (x2) V-lock sticker (x2) Strong double-sided tapes [MADE IN JAPAN] 　　*Need to cut to fit the shape

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation You can attach V-lock to mobile batteries, smartphones, etc. V-lock allows for easy installation and removal https://www.instagram.com/reel/DAxtcEoPWc_/?igsh=cHZtbmpiZXVuc3ht https://www.instagram.com/reel/C_nDnt-PjDM/?igsh=MWZqdXMzOHVxeDlkaw== https://www.instagram.com/reel/C_7pZvGxqpu/?igsh=Y3JwYzRmYjl2dXo1 We have confirmed the installation with many V-mounts, but there may be some wobbling depending on the receiving side of the V-lock. Checked V-mount list ・SmallRig Mini V-Lock Assembly Kit MD2801B ・SmallRig Mini V Mount Battery Plate 2987 ・NEP GP-TS mini V /Pro-X Mini Sharkfin Hotswap Adapter V Mount ●Dimensions 　Approx.　65mm x 42mm x 6.7mm ●Package contents (The first photo is the content) (x2) V-lock Sticker Mini (x2) Strong double-sided tapes [MADE IN JAPAN] 　　*Need to cut to fit the shape

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation This is a 3D printed pocket-sized apple box. 
Since it is printed with PLA, it may deform if placed in a high temperature environment .
We strive to maintain the quality of our prints, but since they are made with a 3D printer, the condition of each printed product is different. And products made with a 3D printer have fine dents due to the characteristics of the print, as shown in the photo. Please understand this before placing an order.
We do not take any responsibility for any damage caused by using this product.
We may take longer to process your order. The pocket apple box is printed in PLA, which is prone to deformation in high temperature environments such as inside a car in summer. Only PLA can choose a wood-like color. ◆◆◆Usage notes◆◆◆ Due to the nature of 3D printing, the strength of the lid drawer is not very high and it may break easily if used incorrectly, so please pull or insert the lid straight. ◆◆◆◆◆◆◆◆◆◆◆◆ ●Dimensions 　100mm x 60mm x 40mm ●Package contents (The first photo is the content) (x1) Full with a lid (x1) Half (x1) Quarter (x1) Pancake (x1) spare lid ＊ "Half" is not actually half the thickness of a "Full" 1/2 the thickness of a "Full"= "Half" ＋ "Pancake" = 20mm 1/4 the thickness of a "Full"="Quarter" = 10mm 1/8 the thickness of a "Full"= "Pancake" = 5mm "Half" = "Quarter" ＋ "Pancake" =15mm

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation It is a boom & umbrella dock that can be fixed with a super clamp. It is possible to connect to the side and install booms side by side. https://www.instagram.com/reel/C94xch6PZIf/?igsh=MXNqNmNvN2J4eGdnMQ== Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with two M5 bolts and one 1/4 inch screw. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. https://www.instagram.com/reel/C94U2EevdWI/?igsh=MWQ0bG9jNTlidHpzYw== In addition, it is possible to connect to the side with one M5 bolt, and by inserting a spacer, it is possible to prevent the next grip from interfering. The lower base part has a structure that does not accumulate water such as rain, making it easy to clean. There is also an optional non -slip sheet. Glue the non -slip sheet with your favorite double -sided tape or adhesive. The whole material uses weather resistance and durable ASA, and the grip uses high -quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with black clamp and orange safety lock 　Please select one of the four grips below with the corresponding diameter. ①Approximately 22-25mm ②Approximately 28-32mm ③Approximately 32-36mm ④Approximately 38-42mm 1 - lower “base” 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation It is a C-stand dock that can be fixed with a super clamp. It is possible to connect to the side and install C-stands side by side. To hold one C-stand, you need a C-stand dock and two super clamps. One C-Stand weighs approximately 5kg-10kg, and most Super Clamps have a maximum payload of 15kg. When connecting the docks, do not load C-Stands that are heavier than the Super Clamp's load capacity. Designed it based on the Avenger C-stand that is mainstream in Japan. The base of the current design is designed so that not only a C-stand, but also a boom or umbrella can be placed on the bottom. If you use the Turtle Base C-stand, which has a protrusion at the bottom, you may hit the bottom, so a base with a larger hole is required. The type is coming soon. [upper “grip” ] Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with one 1/4 inch screw and two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with one M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. [lower “base”] C-stand can be installed at different angles of 90 degrees. https://www.instagram.com/reel/C8HB8bqPbE4/?igsh=eXZpcm81dWx4aG4z It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. In addition, it is possible to connect to the side with two M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the C-stand to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with black clamp and orange safety lock 　Please check the diameter of your stand before purchasing. This grip can hold stands with a diameter of approximately 32-36mm. 1 - lower “base” for C-stands 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation It is a C-stand dock that can be fixed with a super clamp. It is possible to connect to the side and install C-stands side by side. To hold one C-stand, you need a C-stand dock and two super clamps. One C-Stand weighs approximately 5kg-10kg, and most Super Clamps have a maximum payload of 15kg. When connecting the docks, do not load C-Stands that are heavier than the Super Clamp's load capacity. Designed it based on the Matthews C-stand that is mainstream in Japan. The base of the current design is designed so that not only a C-stand, but also a boom or umbrella can be placed on the bottom. https://www.instagram.com/reel/DEMlq8dP8on/?igsh=NHo2Y3cwZHFzemZ0 [upper “grip” ] Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with one 1/4 inch screw and two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with one M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. [lower “base”] C-stand can be installed at different angles of 90 degrees. https://www.instagram.com/reel/C8HB8bqPbE4/?igsh=eXZpcm81dWx4aG4z It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. In addition, it is possible to connect to the side with two M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the C-stand to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with a black clamp and a red safety lock 　Please check the diameter of your stand before purchasing. This grip can hold stands with a diameter of approximately 32-36mm. 1 - lower “base” for C-stands 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts (x2) Y wedge for super clamps

● Precautions before purchasing This product is made of 3D -printed resin, not metal. If you are expecting a metal -like strength, please refrain from purchasing. 3D -printed ones have laminated marks and burrs, and may cause thin scratches in the manufacturing process. Normally, 3D -printed products are less likely to be cleaner like a resin product made in the mold. The strength of the product has been confirmed in normal use, but do not use or make a mistake in the extreme burden. Only those who understand the 3D -printed products or handmade products as described above should order. ● Product explanation B-stock item (used for display, fully functional) It is a C-stand dock that can be fixed with a super clamp. It is possible to connect to the side and install C-stands side by side. To hold one C-stand, you need a C-stand dock and two super clamps. One C-Stand weighs approximately 5kg-10kg, and most Super Clamps have a maximum payload of 15kg. When connecting the docks, do not load C-Stands that are heavier than the Super Clamp's load capacity. Designed it based on the Matthews C-stand that is mainstream in Japan. The base of the current design is designed so that not only a C-stand, but also a boom or umbrella can be placed on the bottom. https://www.instagram.com/reel/DEMlq8dP8on/?igsh=NHo2Y3cwZHFzemZ0 [upper “grip” ] Super clamps can be fixed not only in the horizontal but also vertically. If you fix it horizontal, you can fix it with one 1/4 inch screw and two M5 bolts. If you fix it vertically, remove the non -slip rubber like sheet and you can fix it with one 1/4 inch screw. In addition, it is possible to connect to the side with one M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. [lower “base”] C-stand can be installed at different angles of 90 degrees. https://www.instagram.com/reel/C8HB8bqPbE4/?igsh=eXZpcm81dWx4aG4z It is recommended that the base of the bottom should be tightened with three screws(one 1/4 inch screw and two M5 bolts). Do not fix it with only one or two screws and bolts. In addition, it is possible to connect to the side with two M5 bolt, and by inserting spacers, it is possible to prevent the next grip from interfering. Because it is made of resin, if you repeat the removal and removal, it may be shaved little by little. Let's carefully attach the C-stand to the base:) The whole material uses weather resistance and durable ASA, and the grip uses high-quality and durable TPE. It is currently difficult to obtain ASA materials in a stable manner, and since the filament manufacturers available vary depending on the production period, the way black materials look slightly different. ●Package contents (The first photo is the content) ＊ Super clamps are not included 1 - upper “grip” with a black clamp and a red safety lock 　Please check the diameter of your stand before purchasing. This grip can hold stands with a diameter of approximately 32-36mm. 1 - lower “base” for C-stands 1 - screw and bolt pack (x2) stainless steel 1/4-20 screws, (x4) stainless steel M5-15mm bolts

Please select one of the four grips below with the corresponding diameter. ①Approximately 22-25mm ②Approximately 28-32mm ③Approximately 32-36mm ④Approximately 38-42mm

●Package contents (The first photo is the content) An adapter for for CSD-1 to the Tilta Boulder 36“ Camera Cart *The bottom part is heavily loaded with the weight of the C-stand, so please use a 1/4 inch screw to fix the adapter. 2 - TILTA adapter 4 -M5 bolts 1 - 1/4inch screw